Ld Error on Whirlpool Washer Easy to Fix

As you're washing, your Whirlpool stopped working before the completion of the rinse cycle and surprisingly turned on the water supply. What's the matter?

Does your Whirlpool washer show a 5D error code? You're not alone. Error code 5D is one of the popular error codes that often happen in a Whirlpool washer and it indicates too much soap suds.

In this guide, we'll demystify the Whirlpool washer error code 5D, explaining how it happens, the reasons, and possible solutions to the error.

Are you ready? Let's get started.

whirlpool washed code 5d

Whirlpool Washer Code 5D: How Does It Happen?

Error code 5D indicates excessive suds or soap bubbles in the machine. Whirlpool washing machines have an inbuilt foaming control function that is responsible for reducing soap suds when it's detected.

It controls soap suds by stopping the rotation of the drum and adding more water to the drum load to break the foam bubbles. This automatically increases the rinsing time and it displays the error code while at it.

Your washer will not drain due to these excessive suds and as it continues to break the foam bubbles by adding more water, it displays the error code.

The form suppression mode alternately changes to active if it's successful in breaking the form bubbles and it disappears, otherwise the process continues with the error code 5D displaying. At this point, your Washer is seeking your intervention.

Whirlpool Code Washer Error 5D: Common Causes

The error code 5D could happen for many reasons, some because of inadequate use or error from your end and others because of faulty components in the washing machine. Below are some of the causes of error code 5D.

Excessive Detergent

Excessive detergent is the most probable cause of the error code 5D. If you check the owner's manual, you'll see that your washing machine has the required amount of detergent it needs to wash to prevent residual detergent.

Going above the requirement will result in excessive suds which will, in turn, trigger the error code 5D.

Bad Detergent

Beyond excessive detergent, there is another detergent-related issue that can cause the error code. Using bad or low-quality detergent can also cause errors. High-quality detergent has low sudsing properties so they are the standard recommendations for washing machines.

Using bad quality detergent increases the chances of having excessive suds or bubbles which causes an error. Excess suds can also happen if you use "easy-pour" or " no splash", liquid chlorine bleach.

Clogged Drainage System

Your washing machine drainage system consists of a drain hose, drain filter, sewer entrance, and drain pump. Over time, any of these components might have been blocked by either dirt, lint, debris, or accumulated suds.

If any of these components are blocked, it means there won't be a free flow of water in and out of your washing machine. So, the excessive suds that your washer is trying to remove by diluting it with water won't be able to wash out thereby triggering the 5D error.

Accumulated Detergent Residue

Detergent residue, suds, and debris accumulate in the washer as each washing cycle leaves behind some. Over time if you don't get rid of them, they can cause blockage and this will trigger the 5D error code.

Faulty Foam Sensor

Perhaps you've checked and there's no excessive foam in the drum during the rinse cycle, a faulty foam sensor could also be a probable cause. The sensor might likely be falsely detecting suds in your washer's tub. In fact, this case happens often if the sensor is dirty or faulty.

Water Pressure Controller Failure

Your washing machine will stop spinning and show the 5D error code if the water pressure switch is bad. You can inspect the pressure controller with a multimeter to check if it needs to be repaired or replaced.

Faulty Control Board

The less likely cause of the 5D error code but we can't entirely eradicate the chances of it happening. The control board might have been worn out or had faulty connectors.

Whirlpool Code Washer Error 5D: DIY Fixes

The first step to fixing an error is checking the cause of it. We have provided the likely causes above, the following troubleshoot method will help you fix the error.

Patience

First things first, be patient. When your Whirlpool washer displays the 5D error code, it automatically tries to resolve the issue itself. Your machine will try to diagnose the problem and troubleshoot it especially if it's caused by excessive detergent.

Depending on the amount of excessive suds, The process usually takes 10-20 mins and the machine automatically continues the cycle if the issue is resolved. If the error is not yet solved after this time, you can follow the next steps.

Reset The Washer

Sometimes the error might be due to a glitch or one-time error of the control module. You'll need to reset the washer and put it in cleaning mode to correct the error. You can restart the washer with the steps below.

  • Stop the washing machine and press the power button.
  • Drain the water and open the drum to remove the clothes.
  • Close the lid or door and hold down the PAUSE/CANCEL button for about 3 seconds.
  • Then, your washer should enter the cleaning mode and get everything resolved on its own.

If the control board is bad, then you'll need to change it but you should seek the help of a technician because it's a complex procedure.

Use The Right Amount Of Detergent

Anytime you're using the washing machine, ensure you follow the manufacturer's instructions for the correct proportion of detergent to use. For the 5D error code, you'll need to reduce the amount of detergent and the error should be resolved.

Furthermore, pay attention to the detergent's concentration, and adjust the amount accordingly. Generally, high-efficiency washing machines need less detergent to wash.

Use High-Efficiency Detergent

Whirlpool washing machines require High-Efficiency(HE) detergent. HE detergents are usually easy to know, with the "HE" written boldly on the label.

They are good because of their low sudsing properties and ability to remove stains and clean clothes thoroughly. Using HE products should remove the excess suds.

Check For Clogged Drain System

Your washer might be trying to remove excess suds or forming but because the drainage system is clogged, it's difficult to drain properly.

Check the drainage component such as the drain hose(long hose located behind the washer) to see if there are blockages and clear them accordingly.

Also, check the drain pump filter which is located at the bottom of the washer inside the drum. Its purpose is to trap lint, dirt, and debris so it might have been clogged with some of the items. Clear it accordingly.

If the error persists, it might be a result of a faulty drain pump and you'll need to replace it.

Check The Foam Level Sensor

If there's little or insufficient foam in the tub during the washing cycle, perhaps the form sensor is malfunctioning. You should check the foam level sensor for signs of damage and clean it if necessary. You can check it for damage with the steps below.

  • Turn off your washer and find the access panel. It is usually on top or the rear depending on the type of washer you're using.
  • Find the foam level sensor(check the user's manual to be sure)
  • Disconnect the wiring harness and remove it.
  • Test it with a multimeter to check for continuity, if it's positive you need to replace it.
  • If it's negative, then the sensor is ok and you can just clean it.

Whirlpool Code Washer Error 5D DIY Video

The video below should be of help when you're fixing the error code 5D on your Whirlpool washing machine:

When Do You Call a Repairer?

You should seek the help of a professional when:

  • None of the solutions provided above solve the error.
  • You think either the control board or foam level sensor is faulty

Whirlpool Washer SD Error Code: What Does It Mean?

It should be noted that the error code 5D  is a wrong reading. The actual error is SD. Actually, Most washing machines display error codes in digit form. Consequently, users often misinterpret them because of the way they are written.

Users confuse "S" as "5" because of their similarity on the electronic display and thus refer to error SD as 5D.

Conclusion

A whirlpool error code 5D/SD indicates excessive sud or form in the tub/drum and it's making draining difficult. This error can be caused by excessive or low-quality detergent, a bad draining system, a faulty foam sensor, or a glitch.

The error can be resolved by removing excess soap, using high-efficiency detergent, cleaning the drainage system, and repairing foam level sensors as the case may be.

howematurch.blogspot.com

Source: https://errorlens.com/whirlpool-washer-code-5d/

0 Response to "Ld Error on Whirlpool Washer Easy to Fix"

Postar um comentário

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel